On Saturday, June 26, 2010, Joseph Newman held a 'historic event' demonstration in Denton, TX in which he showed a 3 ton electric motor plus load, in an arrangement that he claimed "basically runs itself". Travis Norman attended and estimates the motor efficiency at between 95 and 125 percent.
|
|
On Saturday, June 26, 2010, Joseph Newman held a 'historic event' demonstration in Denton, TX in which he showed a 3 ton electric motor plus load, in an arrangement that he claimed "basically runs itself". We asked if any of you might be attending, and if you could report on what you saw. Travis Norman responded. He said: "I am an electronic tech and have done free energy research since 1979; and I know how Newman's motor works."
On June 28, he provided the following report: (slightly edited)
Hi Sterling,
I took some pics and shot a video while I was there. One is 9 plus minutes, and the other is 7 plus minutes.
I have been an electronics tech now for 34 yrs now, mostly in the instrumentation field. I was trained in electronics by the Navy back in 1975. I have been researching in the free energy field since 1979. I have a strong science back ground education -- mostly physics and chemistry.
I have followed Joseph Newman's work since I saw his small motor powering a fan. It ran off of 3000 volts at 9 milliamps.
The last video demonstration I saw of his was when this motor ran at 250v at 1 amp under load. He was using a 375 pound mud pump, which I believe is the same pump I saw Saturday. Then he was pumping water up 10 feet and comparing it to a conventional motor pump pumping the same amount up the same 10 foot head at the approx. GPM [gallons per minute] flow-rate.
Saturday the pump was 5 feet above ground, pumping water back into a reservoir on the ground. I estimate the flow-rate was no more than 50 GPM. at 160 rpm at the start of the demonstration. His input power was 60 each 9v alkaline batteries in series.
He started the demonstration at a measured 9.47 volts per battery. After about 1.5 hours of run time he measured the battery at 7.5 volts unloaded. His motor was then running at 115 rpm. it appeared that there was a rpm to voltage input correlation.
When he starts the motor, he starts it by hand and then steps voltage up from about 50v to the full voltage from the batteries in 7 or 8 steps till the motor comes up to speed.
I asked him what the input current was and he said 5 to 15 milliamps. He did not have it metered. 540 volts times 15 milliamps is 8.1 watts.
However in a DVD he handed out to everybody, he was powering the same motor with a veriac auto transformer from the ac line to a step up transformer with rectification for high voltage dc. He measured 22 volts at 2.5 amps which is 55 watts which would explain why his battery pack (65 watt/hr) went technically dead in 1.5 hrs.
The hydraulic power at 50 GPM (max) at a 2.5 PSI head pressure is 54 watts. This is my best estimate of the pump output on the high-side.
He has a high voltage capacitor to capture back emf from his coil and is probably feeding it back into a second coil. He said the voltage was 1000v on this capacitor.
His "runs itself" quote was after he disconnected the battery it ran for 2 minutes under pump load before coming to a complete stop. Some of this might be due to the 477 pound flywheel and the1200-lb magnet in the rotor. How much is due to the back emf on the capacitor is unknown.
From the vagueness of the demonstration I personally place the motor's efficiency between 95% to 125%.
I believe the motor to be more efficient the higher the input voltage.
Data
Explanation from Norman
The hydraulic gpm is based on the observed estimated dimensions of the pump
The 120mahr battery by the 1.5 hour run to dead battery voltage gave the estimated ma draw at the start
His dvd did measure volts and amps and I clock the rpms at 140
55 watts electric and 54 watts hydraulic
The hydraulic estimate is on the high side
His demonstration needs improvement, he is claiming 10 hp out
I didn't see the dvd till I got home and I gave the max estimate in his favor
if his motor puts out 110% and no more than 5000watts shaft max, how much does his motor cost at 7000lbs+ if it is more than 10k dollars it is uneconomical
Photos
Videos
| Joseph Newman eureka demonstration part1 was on Saturday June 26 2010 in Denton Texas. the demonstration was from 11am to 5pm this video is when he started the demonstration up to Q and A. part 2 is of the motor running and pump load. (YouTube; June 28, 2010) |
| (YouTube; June 28, 2010) |
Posters
The following are transcribed from a couple of posters that were on display:
# # #
email: <tmnorman {at} msn.com>
YouTube ID: tfish0
website: http://centripledyne.com/
See also
|
Comments
For openers, those videos have had removal of Newman's abrasive, insulting, angry rants at people simply asking appropriate questions. Not suprisingly, Newman gets upset when anyone asks why after all these years, he can't simply close the loop and do away with the silly batteries. Problem is, when Newman is upset, his true personality emerges. And that reveals him to be an unpleasant, angry, barely coherent whack job. And his machine belongs in a scrap yard.
Fortunately, an impartial observer took another video which you can find here:
(http etc. etc.) youtube [dot]com [slant]user [slant]chrisryanwilliams
Sorry but I can't put a plain URL here! So pls reconstruct it. If you're rushed, start at video #4 time index around 5:50 and 8:30 to watch Newman go bonkers. Strange how that is left out of the video in the article. Maybe the author can tell us why? Also discuss this at: moletrap[dot]co[dot]uk[slant]forum[slant]comments.php?DiscussionID=1348
The question is why doesnt Newman just close the loop. The answer is he cant because his machine wouldnt work. From Newman to Steron to half the other inventor in between, not a single one of these people that come up with these "overunity" devices ever closes the loop. Close the loop and maybe people will take you more serious. Running it off a battery is a joke.
Whoop d Doo. So he used three things that shouldn't be even a consideration.
1) 9V Batteries, why not use a calibrated current source to prove the point???
2) A flywheel will keep an engine running for a short time, we know this back from the days of the John Deere 70 series, etc...
3) Why did you start it by hand? Of course, you don't have enough current to build up the magnetic field to start the process, how about building a pony or goat motor???
Go back to the drawing board, learn some manners, and get your facts straight!
To Eric, Bob, and Mary: Joseph Newman has stood up against a power structure that does not want their fossil fuel empire to crumble. They have threatened his life and they have offered him hundreds of millions of dollars to sell you out. (You and the rest of humanity.) What you see on Mr. Norman and Mr. William's videos is the accumulation of 40 years of injustice - a thousand wounds invisible to the eye, but they are there. Take your daggers out of his back.
I remember this person from about literally 20 years ago. After some initial excitement, I remember that he was discredited. He lived in Mississippi at the time. I lived in a town nearby. In my opinion, nothing to see here, move along.
you guys missed it a shame really because being a south african sience prof i can tell you 1 true fact he was 99 percent there .Pity none of you half wits WITH TODAYS PROCESSING POWER cant work out the true nature of this machine and the small mistake this layman made . anyway before i release the truth know this it will be to guys like creative sience and co who are working towards humanitys greatest invention "simbiotic relationship between the virus "man" and our universe....................................hint: light speed is not a constant..............duh
The earliest identified illustrations are in fact issued on English literary annuals that are in fact completely recognised while in the 1820s toward the 1850s. These ebooks on a regular basis expert fancy bindings that required protection. The belstaff jackets which are in fact utilised inside the immediate entirely enclosed the ebooks like wrapping cardstock and so are in fact sealed shut with polish or glue. The oldest editors belstaff coats now on historical previous was issued in 1829 on an English annual, friendship’s supplying for 1830. each and every solitary belstaff are inside the assortment that entirely enclosed the books. More items on top1 on the internet outlet: http://www.belstaffcoat.com.
Our vibram store is especially dedicated for all the Vibram Five Fingers Shoes and Five Fingers Shoes lovers. Our wholesale vibram store mostly gives all types of lower price Mens Vibram Five Fingers and Womens Vibram Five Fingers that produced in Italy. With it is exceptional quality, exceptional beauty, and ideal Italian craftsmanship, we gives you only the very best Mens Vibram Five Fingers and Womens Vibram Five Fingers so on, which all be produced from the perfect materials. considering cooperated using the vibram outlet skilled manufactures for twenty years, we've strictly handle within the style, good quality of Mens Vibram Five Fingers and Womens Vibram Five Fingers , as for as now the goods are actually exported to more than one hundred nations and areas. http://www.vibram55.com
Got something to say?
Examiner.com is looking for writers, photographers, and videographers to join the fastest growing group of local insiders. If you are interested in growing your online rep apply to be an Examiner today!