Excessive lint build up occurs slowly and gradually. You don't realize it is happening. You think that by cleaning out the lint filter after each use you are doing your job and maintaining the dryer. Not quite!
A full load of wet clothes contains about a half gallon of water. Lint is created from the clothes as water is removed during the drying process. This lint will build up in crevices deep down inside the lint filter trap, and all along the dryer vent hose. At the end of the day, your dryer is the number 1 source of fire in the home.
In 1999 the U.S. Consumer Product Safety Commission (USCPC) developed a report called the “Report on Electric and Gas Clothes Dryers.” In that report they determined that of the 15,000 fires studied in one year, electric dryers were over 2.5 times more likely to be the cause of the fire than gas dryers. Fires originated most frequently from two places: dryer venting and the lint trap.
What are the warning signs that dangerous lint build up is occurring in your dryer and venting system? Well, the symptoms may include:
Clothes take longer and longer to dry
Clothes don't fully dry
Clothes are hotter than normal at the end of the drying cycle
The outside of dryer gets very hot
The outside exhaust vent flapper does not open very much
Laundry room becomes more humid than usual
Burnt smell is evident in the laundry room.
Dryer Vent Cleaning Brush Kit
To effectively clean your dryer and dryer vent hoses / venting system, you will need a special brush for this dryer repair. Vacuum attachments alone do not work as well because they do not agitate the lint to separate it from the duct and it is this physical agitation that is important.
There are a few different dryer duct cleaning brush kits or tools out there. One great product is The Linteater. The brush kit will come with a long bristle brush to clean the lint screen but the important component is the specialized round, thick bristled brush that cleans out the round 4" dryer duct. The brush tip fastens to a flexible fiberglass shaft that can be added onto to increase the length.
Remove the Lint Trap Filter:
This is the step you are most familiar with and probably do on a regular basis such as after each load. As a matter of fact, this step is probably all you have ever done, just like 90% of the population. Although this step of cleaning the lint filter is important, it does not solve the problem of lint build up in the dryer or in the ducting. However it is important as a first line of defense and we need to do it, so:
Remove the lint screen by pulling it straight out
Clean the screen of any lint by gently brushing it with the fine bristled cleaning brush.
Vacuum Lint Trap Housing Cavity:
OK, now we start getting to areas of the dryer where you're going to find all kinds of lint hidden away. The next area you want to clean is the lint trap housing cavity, the cavity from which you pulled the screen out. You'll need the long flexible fiberglass handle of the brush kit to get into this area.
Extend the brush all the way into the bottom of the cavity
Using a gentle and slight twisting motion, pull out the brush to expose the clumps of lint it has removed
Using a household vacuum cleaner or shop vacuum, vacuum the brush head clean of any lint
Repeat this process until there is no more lint that can be removed from the cavity.
Disconnect Sections of Dryer Vent:
To properly disassemble and reassemble the duct sections, proceed as follows:
Unplug the dryer;
Turn off the gas valve at the dryer (if it is a gas dryer)
Disconnect the duct joint closest to the dryer
Gently pull the dryer away from the wall
Disconnect the remaining sections of dryer duct.
Insert and Rotate Dryer Duct Brush into Ducting
Next we get a little dirty, but it's worth it. You're going to be greatly reducing the #1 risk of fire in your home (dryer fire) by doing this.
Fasten the duct brush end to the flexible fiberglass shaft;
Fasten as many threaded shaft sections together as needed.
The other end of the brush can either be used to turn the brush manually, by hand, or it can be fastened into a variable speed drill.
Insert the duct cleaning brush into the dirty lint lined duct and sweep it clean by using a rotating motion while pushing the brush back and forth;
Go slowly and if you use a drill, make sure to use a slower speed. Once most of the lint debris is removed you can go faster to really clean the duct out.
The Duct Cleaning Process: Before, During and After
Properly performed the duct cleaning process will look like the photo in the article slideshow (and this is pretty hard to mess up, I mean you're brushing out a pipe for Pete's sake).
Perform this cleaning procedure for each section of dryer duct and all the elbows. Also make sure the exhaust discharge cap on the outside of the house is cleaned out and has no lint obstruction.
Amount of Lint Removed in One Cleaning
It is amazing how much dangerous lint will be removed from your dryer ducting when the cleaning is complete. The slideshow photo shows the incredible amount of lint removed from just 8-10 feet of duct and two elbows.
Prior to this cleaning, the dryer always had its lint screen cleaned after every few loads and the dryer was working "fine" it just seemed to take a little long to dry clothes.
This is why dryer fires are so dangerous, the lint builds up over time and you get used to the progressively inefficient drying performance of your dryer. All the while, lint is dangerously building up.
Reassemble Dryer Ducting
Once the dryer ducting is cleaned out, you now reassemble the duct.
Attach an adjustable rigid 90 degree elbow to the exhaust end of the dryer. Do not use a semi-rigid flexible duct as an elbow out of the dryer. As you can see in the photo, the semi-rigid duct can kink when the dryer is pushed back into place, thereby causing a major obstruction to exhaust flow.
Attach all rigid metal and semi-rigid ductwork sections with a 4" worm-drive stainless steel duct band clamp.
Turn on gas valve if you have a gas dryer..
Plug in dryer.
Make sure lint screen is in place.